Ordnance Maintenance U.S. Rifles, Cal. .30; M1, M1C (Sniper's), and M1D (Sniper's) TM 9-1275 War Department Technical Manual
Washington DC: United States, War Department, c1947. Appears to be a reprint without information as to source. Wraps. iii, [1], 104, [4] pages. Illustrations. This manual supersedes TM 9-1275, 6 November 1942, including C 1, 15 May 1943; TB 23-5-6, 5 June 1944; TB ORD 207, 28 September 1944; OFSTB 9-1275-5, 28 June 1943; and so much of TB ORD 272, 26 March 1945, as pertains to materiel covered in this manual. This manual represents the state of knowledge and the standards of practice after consideration of the experience gained during the Second World War. Information on Sniper rifles is extremely scarce. Contents include: Introduction; INspection Prior to Disassembly; Tools, Gages, and Fixtures; General Maintenance; Barrel and Receiver Group; Trigger Housing Group; Stock and Hand Guards; Equipment; Function Firing and Final Inspection; Malfunctions and Corrections; Appendix References; and Index. This manual is published for the information and guidance of ordnance maintenance personnel. It contains detailed instructions for inspection, disassembly, maintenance, and repair of the U.S. rifle, cal. .30, M1; U.S. rifle, cal. .30 M1C (sniper's); and the U.S. rifle, cal. .30, M1D (sniper's). This manual does not contain general assembly or disassembly or information which is intended primarily for the using arms, since such information is available to ordnance maintenance personnel in FM 23-5. Where "repair tolerances," as opposed to tolerances for new manufacture have been set up, such repair tolerances will continue in use. If additional tolerances or variations are desired, submit a specific request to the Chief of Ordnance. Only rifles having the new spline-type gas cylinder are to be rebuilt. The receivers on rifles having the old type gas cylinders are of early manufacture, and cause "eleven o'clock" feed stoppages. They are identified by the top of the front feed rib being cut away instead of coming up to a square corner. Since the M1, M1C, and M1D rifles are basically the same mechanically, as well as in operation and functioning, the disassembly, assembly, inspection, maintenance, and repair are covered generally. Characteristics: The U.S. rifles cal. .30, M1, M1C, and M1D are gas-operated, clip-loaded, air cooled, semiautomatic shoulder weapons. These rifles may be equipped with gun sling M1907 (leather), or gun sling M1 (webbing). When desired, grenade launcher M7 or M7A1, or bayonet M1 may be used with the rifles. Difference Between Models: The U.S. rifles cal. .30, M1, M1C, and M1D are basically the same. However, rifles of early and present manufacturer of the same model may differ somewhat due to changes in design of some of the component parts. The U.S. rifle M1C (sniper's) is the standard U.S. rifle M1 with telescope M81 or M82 mounted on the receiver and a cheek pad laced to the stock. The flash hider M2 is furnished as an accessory with the M1C and M1D models. The U.S. rifle M1D differs from the U.S. rifle M1C (sniper's) only in the design of the telescope mount and bracket. On the M1C model the telescope is held in a removable mount having a dovetailed slide mating with that of a bracket permanently attached to the receiver and locked in place by means of two locking screws. On the M1D model, the telescope is held in a removable mount which in turn is attached to a fixed base on the barrel of the rifle by means of one screw and dowel pin. Condition: Good.
Keywords: Military Manual, Technical Manual, M1, M1C, M1D, Sniper, TM 9-1275, Telescope, Inspection, Disassembly, Barrel, Receiver, Trigger Housing, Equiment, Malfunctions, Gages, Fixtures, Hand Guard, Function Firing
[Book #83960]
Price: $200.00